• Home to the ORIGINAL Seat Jackers
  • Lifetime Guarantee
  • FAST & FREE shipping (USA)
What are you Looking for?
SHOPPING CART

No Products in the Cart
TOTAL:
$0.00
PROCEED TO CHECKOUT
VIEW CART
img

title

  • details
qty X
price

Toyota Adjustable Seat Jackers (2019+ RAV4 / 2020+ Highlander / 2021+ Sienna)

INSTALL INFO

FITS

  • 2019+ Toyota RAV4
  • 2020+ Toyota Highlander
  • 2021+ Sienna

DIFFICULTY

Tools Needed

  • 17mm Socket
  • T50 Torx Bit
  • 2.5mm Allen Key
  • Torque Wrench
  • Blue Loctite

Included Parts

  • 2 - M10 1.25 x 40mm Hex Head Bolt
  • 2 - M10 1.25 x 60mm Hex Head Bolt
  • 2 - Lockable Top Seat Jacker Blocks (1 out dent)
  • 2 - Lockable Middle Seat Jackers Blocks (2 out dents)
  • 2 - Long Slotted Seat Jacker (bottom)

 

IMPORTANT NOTES

Desert Does It will not be liable for any loss, damage, or injury directly or indirectly from the use or the inability to determine the use of these products. Before using or installing, the user shall determine the suitability of the products for its intended use, and the user shall assume all responsibility and risk in connection therewith. Any modifications to your vehicle are done at your own risk.

INSTALLATION INSTRUCTIONS

General Note: To help prevent cross threading during installation, we recommend verifying bolts and threads by taking the applicable bolts and threading them in by hand to the corresponding hole.


  1. Step One: Remove any plastic trim at the feet of your seat. Remove both front factory seat base bolts and loosen the two rear seat bolts but do not remove them.
  2. Step Two: Lift the front seat by pushing back on the headrest or by asking a helper to pull from the back seat.
  3. Step Three:
    1. .5 Inch Lift/One Seat Jacker Shim - Choose any of the Seat Jackers shims and put one at the front seat mounting point, place the stack in between the front seat rail and your carpet.
    2. 1” Lift/ Two Seat Jacker Shims - Take the #1 and #3 Seat Jacker Shims and stack them so the engraved numbers are facing up. Take the provided stainless steel flathead bolt and thread it through the countersunk hole on the RIGHT of the #3 Seat Jacker. The Stainless Hardware is for centering the shims only. Place the Seat Jacker stack in between the front seat rail and your carpet at the front seat mounting point.
    3. 1.5” Lift/Three Seat Jacker Shims - Take the #1, #2, and #3 Seat Jacker Shims and stack them in order so the engraved numbers are facing up. Take the provided stainless steel flathead bolt and thread it through the countersunk hole on the LEFT of the #3 Seat Jacker. The Stainless Hardware is for centering the shims only. Place the Seat Jacker stack in between the front seat rail and your carpet at the front seat mounting point.
  4. Step Four: If using one shim, use the provided 40mm Hex Bolt. If using two or more shims, use the provided 60mm Hex Bolt. Take the provided M10 hex head bolt and thread it through the seat rail, through the Seat Jackers, and into the floor of the vehicle.
    *IMPORTANT – IF THE SEAT RAIL HOLE DOES NOT LINE UP, LIFT UP THE SEAT RAIL .25 INCHES AND THREAD IN THE BOLT A COUPLE OF THREADS. IF NEEDED ADJUST THE SEAT RAILS ONE AT A TIME TO GET EVERYTHING TO LINE UP.
  5. Step Five: Torque two front bolts and two rear bolts to 27ft-lbs.
  6. Step Six: Reinstall any plastic trim pieces that were removed in Step One.

 

BACK TO TOP